Refine your search
Collections
Co-Authors
Journals
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z All
Dabade, Uday A.
- Investigation of High Pressure Coolant Assisted Turning of Inconel 718 Using Taguchi and RSM Based Desirability Function
Abstract Views :251 |
PDF Views:3
Authors
Affiliations
1 Walchand College of Engineering Sangli, Maharashtra, IN
2 Dept. of Mechanical Engineering, Walchand College of Engineering Sangli, Maharashtra, IN
1 Walchand College of Engineering Sangli, Maharashtra, IN
2 Dept. of Mechanical Engineering, Walchand College of Engineering Sangli, Maharashtra, IN
Source
Manufacturing Technology Today, Vol 15, No 9 (2016), Pagination: 22-30Abstract
Inconel 718 is one of the widely used superalloy of Nickel used in aerospace applications. It is also considered as "Difficult to Cut" metal. In present analysis a high pressure coolant (HPC) is introduced in cutting zone to check performance of HPC while turning Inconel 718. Experiments are carried out using a high pressure coolant range between 20 to 80 bar. Taguchi methodology is used for design of experiment (DoE). ANOVA and AOM plots are used for analysis of surface roughness. Response optimization is done with Response Surface Methodology based desirability function. All the cutting parameters are found to have significant effect on surface roughness at 95 % confidence level. The optimum process parameters for surface roughness are 80 bar pressure, 67.87 m/min speed, 0.1 mm/rev. feed and 0.5 mm depth of cut.Keywords
High Pressure Coolant, Inconel 718, Surface Roughness, Taguchi Methodology, ANOVA.- Investigation and Optimization of Inconel-718 during Dry EDM
Abstract Views :261 |
PDF Views:0
Authors
Affiliations
1 Department of Mechanical Engineering, Walchand College of Engineering, Sangli, Maharashtra, IN
1 Department of Mechanical Engineering, Walchand College of Engineering, Sangli, Maharashtra, IN
Source
Manufacturing Technology Today, Vol 18, No 9 (2019), Pagination: 52-58Abstract
Dry electric discharge machining (EDM) is a new process in which the liquid dielectric is replaced by a gaseous as a medium. The flow of high velocity gas through hollow pipe tool electrode into the gap provides removal of debris and prevents excessive heating of the tool and work piece at the discharge spots. Keeping literature review into consideration and trial experiment in this paper, an attempt has been made by selecting compressed air as a dielectric medium, with Inconel – 718 as a work piece material and copper as a tool electrode. Experiments are performed using Taguchi DoE L27 orthogonal array to observe and analyze the effects of different process parameters to optimize the response variables such as material removal rate (MRR), tool wear rate (TWR) and surface roughness (Ra). In the current work, a unit has been developed to implement dry EDM process on existing oil based EDM machine.Keywords
Dry Electrical Discharge Machining (Dry EDM), Material Removal Rate (MRR), Surface Roughness (Ra), Tool Wear Rate (TWR), Taguchi Method, Analysis of Variance.References
- Leao, Fabio, N; Pashby, Ian R: A review on the use of environmentally friendly dielectric fluids in electrical discharge machining, ‘Journal of Materials Processing Technology’, 149 (1-3), 2004, 341-346.
- Kunieda, M and Yoshida, M: Electrical Discharge Machining in Gas Tokyo University of Agriculture and Technology, Department of Mechanical Systems Engineering Tokyo Japan’, 1996.
- Khundrakpam, Nimo Singh; Brar, Gurinder Singh; Deepak, Dharmpal: Grey-Taguchi Optimization of Near Dry EDM Process Parameters on the Surface Roughness, 'ICMPC 2017', vol. 5, no. 2, 2018, 4445-4451.
- Macedoa F T B; Wiessner, M; Hollenstein, C; Kuster, F; Wegener, K: Investigation of the Fundamentals of Tool Electrode Wear in Dry EDM, ‘7th CIRP Conference on High Performance Cutting (HPC VII)’, vol. 46, 2016, 55-58.
- Saha, S K & Choudry, S K: Multi–objective optimization of the dry electric discharge machining process, hal-00396875, version 1- 4, 2009.
- Uhlmann, Eckart; Schimmelpfennig, Tassilo-Maria; Perfilov, Ivan; Streckenbach, Jan; Schweitzer, Luiz: Comparative Analysis of Dry-EDM and Conventional EDM for the Manufacturing of Micro holes in Si3N4-TiN, ‘18th CIRP Conference on Electro Physical and Chemical Machining (ISEM XVIII)’, vol. 42, 2016, 173-178.
- Shirguppikar, Shailesh S; Dabade, Uday A: Experimental Investigation of Dry Electric Discharge Machining (Dry EDM) Process on Bright Mild Steel, 'IMME17', vol. 5, 2018, 7595-7603.
- Govindan, P and Joshi, S: Investigations into performance of dry EDM using slotted electrodes, ‘International Journal of Precision Engineering and Manufacturing', vol. 12, no. 6, 2011, 957-963.
- Govindan, P and Joshi, S: Experimental characterization of material removal in dry electrical discharge drilling, ‘International Journal of Machine Tools & Manufacture’, vol. 50, no. 5, 2010, 431–443.
- Tao, J; Shih, AJ; and Ni, Jun: Experimental Study of the Dry and Near-Dry Electrical Discharge Milling Processes, ‘Journal of Manufacturing Science and Engineering’, vol. 130, 2008, DOI:10.1115/1.2784276.
- Phadke M S : Quality engineering using robust design, Prentice Hall, Eaglewood Cliffs, 1989
- Experimental Investigation and Parametric Optimization of Micro Holes on Inconel 718 using Developed µ-AJM Set-up
Abstract Views :267 |
PDF Views:0
Authors
Affiliations
1 Department of Mechanical Engineering, Walchand College of Engineering, Sangli, Maharashtra, IN
1 Department of Mechanical Engineering, Walchand College of Engineering, Sangli, Maharashtra, IN
Source
Manufacturing Technology Today, Vol 18, No 12 (2019), Pagination: 35-42Abstract
Nowadays, trends in the manufacturing industry, micromachining on difficult to machine materials such as ceramics, silicon, glass, alloys of titanium and nickel, etc. is a challenging task. Difficult to machine materials are widely used for MEMS, electronic devices, medical and aerospace industries. The higher cost is associated with the machining of these materials. Mostly µEDM, µECM and µLBM process is used to create micro features. In this paper, an attempt is made to machine a micro-hole on Inconel 718 using developed in house Micro Abrasive jet machining set-up (µ-AJM). This process has several notable advantages such as minor heat-affected zones (HAZ) and cutting forces, high machining versatility and flexibility. The experiments are planned with the proper array. The experimentally measured values of different quality characteristics have been taken as hole diameter, MRR, and machining Time. It can be noticed that Standoff Distance (SOD) is an important factor and other factors Air pressure and abrasive mesh size does not show sufficient significance. The parametric effect of different most significant input process parameters on quality characteristics has been discussed. ANOVA results showed that the Stand of Distance was the most effective parameter. The optimal condition where Abrasive size (50,100) Mix standoff distance 1 mm and inlet pressure (P1) 9 bar for minimizing the hole Diameter and lesser machining time and higher MRR on Inconel 718 material.Keywords
Micro-abrasive Jet Machining (MAJM), Inconel 718, Material Removal Rate (MRR), Taguchi Method, Analysis of Variance (ANOVA).References
- EI-Domiaty, A; Abd EI –Hafez, HM and Shaker, MA: Drilling of glass sheets by abrasive jet machining, 'World Academy of Science, Engineering and Technology', 56, 2009.
- Yamahata, C; Lacharme, F; Burri, Y and Gijs, MAM: A ball valve micropump in glass fabricated by powder blasting, Sensors Actuators, 'B Chem.', vol. 110, no. 1, 2005, 1–7.
- Ghobeity; Papini, M and Spelt, JK: Abrasive jet micro-machining of planar areas and transitional slopes in glass using target oscillation, 'J. Mater. Process. Technol.', vol. 209, no. 11, 2009, 5123–5132.
- Abhishek, K; Hiremath, SS: Machining of micro-holes on sodalime glass using developed micro-abrasive jet machine (μ-AJM), 'Proc.Technol.', 25, 2016, 1234–1241.
- Suresh, R; Sohit, RK; Shapur, K: Abrasive jet machining for micro-hole drilling on glass and GFRP composites, 'Mater. Today Proc'., 5, 2018, 5757–5761.
- Jagannatha, N; Hiremath, SS; Sadashivappa, K: Analysis and parametric optimization of abrasive hot air jet machining for glass using Taguchi method and utility concept, 'Int. J.Mech. Mater. Eng.', vol. 7, no. 1, 2012, 9–15.
- Jagannatha, N; Somashekhar, SH; Sadashivappa, K; Arun, KV: Machining of soda lime glass using abrasive hot air jet: an experimental study, 'Mach. Sci. Technol.', vol. 16, 2012, 459–472.
- Getu, H; Ghobeity, A; Spelt, JK and Papini, M: Abrasive jet micromachining of polymethylmethacrylate, 'Wear', vol. 263, no. 7-12 SPEC. ISS., 2007, 1008–1015.
- Tomy and Hiremath, SS: Machinability and characterisation of machined hole on quartz using developed µ-AJM set-up, 'Adv Mater Process Technol'., vol. 5, no. 2, 2019, 242–257.
- Prasad, SR; Ravindranath, K and Devakumar, MLS: Experimental investigation and parametric optimization in abrasive jet machining on nickel 233 alloy using WASPAS and MOORA, 'Cogent Eng'., vol. 5, no. 1, 2018, 1–12.
- Ally, S; Spelt, JK and Papini, M: Prediction of machined surface evolution in the abrasive jet micro-machining of metals, 'Wear', vol. 292–293, 89–99, 2012.
- Shafiei, N; Getu, H; Sadeghian, A and Papini, M: Computer simulation of developing abrasive jet machined profiles including particle interference, 'J Mater Process Technol'., vol. 209, no. 9, 2009, 4366–4378.
- Vanmore, V.V; and Dabade, UA: Development of Laval Nozzle for Micro Abrasive Jet Machining [MAJM] Processes, 'Procedia Manuf'., vol. 20, 2018, 181–186.
- Abhishek, K; Hiremath, SS; Kumar, A and Hiremath, SS: Improvement of Geometrical Accuracy of Micro Holes Machined Through Micro Abrasive Jet Machining, 'Procedia CIRP', vol. 46, 2016, 47–50.
- Burzynski, T and Papini, M: Modelling of surface evolution in abrasive jet micro-machining including particle second strikes: A level set methodology, 'J Mater Process Technol'., vol. 212, no. 5, 2012, 1177–1190.
- Getu, H; Ghobeity, A; Spelt, JK and Papini, M: Abrasive jet micromachining of polymethylmethacrylate, 'Wear', vol. 263, no. 7-12 SPEC. ISS., 2007, 1008–1015.
- Achtsnick, M; Hoogstrate, M and Karpuschewski, B: Advances in High Performance Micro Abrasive Blasting, 'CIRP Ann - Manuf Technol'., vol. 54, no. 1, 2005, 281–284.
- Ghobeity, Getu, H; Krajac, T; Spelt, JK and Papini, M: Process repeatability in abrasive jet micro-machining, 'J Mater Process Technol'., vol. 190, no. 1–3, 2007, 51–60.
- Zhang, L; Kuriyagawa, T; Yasutomi, Y and Zhao, J: Investigation into micro abrasive intermittent jet machining, 'Int J Mach Tools Manuf'., vol. 45, no. 7–8, 2005, 873–879.
- Balasubramaniam, R; Krishnan, J and Ramakrishnan, N: Experimental study on the abrasive jet deburring of cross-drilled holes, 'J Mater Process Technol'., vol. 91, no. 1, 1999, 178–182.
- Vanmore, VV and Dabade, UA: Experimental and Parametric Optimization of Micro Holes on ANSI 304 Using Micro Abrasive Jet Machining (MAJM), 'Procedia Comput Sci'., vol. 133, 2018, 620–626.
- Barrado, E; Vega, M; Pardo, R; Grande, P and Del Valle, JL: Optimisation of a purification method for metal-containing wastewater by use of a Taguchi experimental design, 'Water Res'., vol. 30, no. 10, 1996, 2309–2314.